>>> *ENGLISH *简体中文
产品介绍 | 图片展示 | 视频演示 | 工作演示 | 注意事项 | 公司方位图 | 资质证书 | 型号与价格 |
来宾留言 | 市场分析 | 商标查寻 | 机型结构图 | 主要技术参数 | 开发部的同志 | F145型说明书 | F165型说明书 |
返回首页 |     飞万达小吊机 | 重庆分公司 | F165型装配图 | 返回首页 |

::::::,飞万达在09推出新款F165型抹灰机具有自动定位遥控调整。激兴自动找平等特征,欢迎各位顾客来公司考查咨询。公司为你报销路费. . .::::::

F165型抹灰机概述

  飞万达F165 型粉墙机是在 123 型粉墙机的基础上,加装自动定位遥控装置,激光自动找平系统,把光电技术融进粉墙机中,实现了光、机电完美的统一。采用中间传动方式,使搅叶输出的力度大而均匀。可伸缩式立杆,进出工地高度在 两米 内不需要拆任何部位,伸缩式大料斗,粉墙高度在 3.5 米 以下装满灰可一次性粉到顶部,不需要一边上升一边加料。底座上面装的万向轮,移动方便。设计巧妙的机械自动锁顶和机械自动抓地装置,大大提高了工效,更利于所粉墙面的平整、垂直。操作简单,提升自如。

技术参数:

?粉墙高度: 3.6 米以下自定。特殊机型可到 5 米以下。
工作效率 ≥ 3 ㎡ /min 。
?功率: 1.3KW 或 2.0KW
?墙面垂直度≤ 3mm 。(符合部颁施工标准)
?外型尺寸: 1200mm × 800mm × 3470mm (包装尺寸:主机 1200 × 800 × 600 立杆: 1800 × 1000 × 800)
自重: 150kg 左右。
电力:两相( 220V )。

主要结构

  动力装置、减速装置、支架升降装置、控制系统、自动定位遥控装置、激光自动找平系统、提升装置、链轮传动装置、带大容量可收缩灰斗的活动粉墙装置、带脚撑器底座、带顶撑和斜撑的上架装置。

Type plastering machine summarizes F165

Beijing FWD Technology Company issued the latest patent product F165 Wall Plastering Machine. The product is made with advance technology. It is small in balk, low in weight, easy to control, safe to use and convenient to install and move. It can save material, labour, time and enhance the project quality. It can shorten the work time, meanwhile the investment is low but the efficiency is high. It is very proper to use in the building company or the special wall plastering worker. The fact proves that the appearance will bring a revolution to the structure profession.

Technical parameter:

Whitewashed wall altitude: : Below 3.6 meters from decides. The special type may to 5 meters below . Working efficiency : >= 3 ㎡ /min. Power: : 1.3KW or 2.0 KW Wall surface verticality : <= 3mm . (Conforms to proclaim construction standard) Outlook size: 1200 mm * 800 mm * 3470 mm (packing size: Main engine 1200 * 800 * 600 : 1,800 * 1,000 * 800) Dead weight: About 150kg . Electric power: Two (220V)

Main structure

The power unit, the decelerating device, the support elevating gear, the control system, the automatic positioning remote control installment, the laser automatic seek stable system, the lifting gear, the chain wheel transmission device, raise the capacity may contract ash hopper ,the active white washed wall installment, the belt foot supporting foundation, the belt crown stay and top carriage installment.

安装使用 :

  首先把立柱部件内的小钢丝绳底部顶端穿入底座导轮内,把它连接到底座紧绳器内,把钢丝绳用卡子卡紧,然后架起两侧立柱,把机器移到所需的地方。

?  开两端紧绳器,逐步把立柱往上升,直到所需要的高度,然后锁定紧绳器。

?  接好电源,开动倒开关,同时拽工作轮一侧定轮槽内的钢丝绳,取出上架部件,装在立柱上。

?  找开主机盖板,先对减速机加润滑油,然后对所有转动轮轴部位、立柱管及两个滑部件进行涂油滑处理,使主机顺立柱上下滑动自如,不能有卡死现象,以免发生其它机件损坏。

?  润滑处理后,启动倒正开关,调试升降,空机磨合应在半小时以上。

?  调整机体与墙壁之间距离,根据要求,确定抹灰厚度,一次抹灰厚度二公分以下,然后把底座和顶架调节厚度的调距装置调整好,锁定上下顶紧器。也可再用钢管抵紧上梁。

?  先将所需灰料一次性装入灰料斗内,启动顺开关,自下而上开始抹灰,直至顶梁。

?  机器粉刷到顶后,电源会自动关闭,松去上下顶紧器,取下斜撑,然后将机器移动到另一边要粉刷的墙面,将灰斗逐步放下,进行第二次粉刷(操作过程同上)。

?  机器使用完毕,要及时清洗机器。先清洗机器内各传动部件,然后清洗外壳、灰斗搅拌轴,防止水泥凝固。

?  粉墙前的准备工作:

 

粉墙前的准备工作:

(一)、墙面处理:

打点(俗称打疤)

 按机器的作业特点上下打点,每点面积 2 5c ㎡左右。表面平整,上部的点和底部的点在同一垂直面上,各点均在同一平面内。如有厚度超过 2cm 的地方,应预先补平。

打毛湿水。如果是浇铸的水泥墙、轻质砖墙或者墙面很光滑的,粉墙之前需预处理。预处理方法是:( 1 )湿水:在粉墙前 2 - 4 小时对墙面喷水。( 2 )打毛:将仿瓷涂料胶水或用 PVA (聚乙烯醇) 6 - 7 公斤加水 100 公斤加热溶解的自制胶水加入到水泥浆中,搅拌均匀成稀料,刷抹在墙上,使墙面粗糙。正式粉墙前:如墙面很干燥,还需湿水。

(二)、砂浆配方配比:

根据工程要求及各地方的要求而定。

一般是:
1 、石灰膏+沙子+水
2 、水泥+石灰膏+沙子+水
3 、水泥+沙子+水(水泥砂浆)
这里重点介绍水泥砂浆:水泥砂浆配比(仅供参考)

水泥︰中砂︰水︰水泥砂浆外加剂= 100 ︰ 250 ︰ 10 0 ~ 150 ︰ 1 - 2

水泥砂浆外加剂,又叫砂浆王,也叫 Cm 3 。呈褐色或灰黄色粉末。加此料是施工标准的要求。如果有些工程可以加石灰膏,则添加 20% 左右的石灰膏后,可不添加水泥外加剂。

遥控使用

飞万达牌粉墙机自动定位遥控装置,是我公司独家研制生产的,该系统由微型调速电机,特制的自动控制电路盒及遥控器,螺旋伸缩顶杆等组成。结构简单,接线简便,操作方便,维修简易。

控制电路电源: 220V
遥控器: 采用点动控制,即按住按钮电路工作,松开就停止工作。

四个按钮的作用:

按钮 B 和 C 控制一端电机 按住 B 或 C 螺旋顶杆往外伸,松开停止。
按钮 C 和 A 控制另一端电机 按住 D 或 A 螺旋顶杆往外缩,松开停止。

注意:
# 两边电机不能同时作业,即每次只能按一个按钮。
# 遥控器不能浸水或重摔,如果遥控距离缩短或遥控器上发光灯变暗须更换 12V23A 高电流电池。
# 注意保护好遥控器,如丢失须到我公司另行配制。
# ? 控制电路盒不能浸水,注意防潮。节省灰料 10% 左右。

 

Installs the use :

First, penetrate the column part in small steel wire base peak the foundation in, connects it in the foundation tight rope is tight the steel wire with the clip card, however the rear frame gets up two sides columns, transfers to the machine the place which needs. Operates the beginnings and ends tight rope, gradually the column toward the rise, until the altitude which needs, then locks the tightrope. Meets the power source, the start but actually switch, simul taneousl yentrains in a work turn of side tightening pulley trough the steel wire, takes out the top carriage part, installs on the column. Gives change the main engine lap, first to the speed reducer applyoil, then to all rotations wheel axle spot, the column tube and two slippery parts carries on spreads slick processing, causes the main engine to skid along the column about freely, cannot have the deactivation phenomenon, in order to avoid has other part damages. After lubrication processing, the start switch, the debugging fluctuation, is but actually spatial machine wears in should above half hour. Between the adjustment organism and the wall is away from, according to requests, definite plastering thickness, below plastering thickness two centimeters, then is apart from the foundation and the upper frame adjustment thickness accent the installment to adjust, about locking goes against tightly. Also may again use the steel pipe to arrive tightly puts up the main beam. First, will need the ash material disposable to load the ash bucket in, the start is suitable the switch, from bottow to top starts the plastering, until top-beam. After the machine whitewashes will go against about, the power source can the automatic shut-off, the pine go goes against tightly, takes down lifted rack, then moves the machine the wall surface which whitewashes to another defensive point on the frontier, gradually will lay down, carries on second time whitewashes (operating process same). The machine use finished, must promptly clean the machine. First cleans in the machine various transmissions part, then the clean outer covering stirs the axis, prevents the cement setting. In front of whitewashed wall preparatory work:

In front of white washed wall preparatory work:

(1)the wall surface processing: Arranges (popular name to hit scar) Arranges according to about the machine work characteristic each area about 25 c ㎡ .the outside is neat, upside spot and base spot in identical Vertical plane on, each in identical plane. If the thickness tosur pass 2cm on some place, should make up in advance evenly. Damages the wet water. If the casting cement wall, the light quality brick wall or the wall surface very smooth, in front of white washed wall must pretreat. The pretreatment method is: (1) wet water: In white washed wall before 2 - 4 hours to spraying wet water to the wall. (2) damages: Will imitate the porcelain coating glue water or (polyvinyl alcohol) 6 - 7 kilograms adds water 100 kilograms with PVA to heat up dissolved the self-made glue water to join to the cement mortar in, will stir evenly becomes Sparse material, will brush wipes on the wall, will cause the wall surface to be rough. In front of official whitewashed wall: If the wall surface is very dry, but also needs the wet water

(2)The mortar formula allocated proportion:

Decides according to the project request and various places request. Generally is: 1st, lime paste + sand + water 2nd, cement + lime paste + sand + water 3rd, cement + sand + water (cement mortar) here key introduction cement mortar: The cement mortaral located proportion (only supplies reference)

Cement: Center granulated substance :water : cement mortar sur- medicinal preparation = 100 :250 : 100 ~ 150 :1 - 2 Cement mortar sur- medicinal preparation, also is called the mortar king, also calls Cm 3. Assumes brown or the yellow powder. Adds this material is constructs the standard request. If some projects may add the lime paste, after then increases 20% about the lime paste, but does not increase the cement sur- medicinal preparation. Matters needing attention:

 

The adjustment remote control fixing position is put into

Ocalization adjustment remote control use the brand of FWD white washed wall machine automatic positioning remote control installment, is our company own development production, this system by the miniature velocity modulation electrical machinery, the automatic circuit box and there mote control which specially makes, the spiral expansion and contraction roof bar and so on composes. Structure simple, the wiring is simple, ease of operation, service simple. Control circuit power source : 220V

Remote control : Uses the spot to move the control, namely holds down the button electric circuit work, the pine opens the knock off.

Four buttons functions : Button B and C control an end electrical machinery to hold down B or the C spiral roof bar toward outside is stretched, the pine opens stops. Button C and A control another end electrical machinery to hold down D or the A spiral roof bar toward outside shrinks, the pine opens stops.

Attention: Two sides electrical machinery cannot simultaneously the work, namely each time only be able according to a button. The remote control cannot immerse or again fall, if on remote control range attenuation or the remote control shines the lamp to change darkly must replace the 12V 23A high electric current battery. The attention protects the good remote control, if loses must arrive at our company separate configuration. Control circuit box cannot immerse, the attention is moisture-proof. Saves the ash material about 10%

 

故障现象

故障原因

排除方法

 

 

   按开关不运行

•  停电

•  手控开关线未接好或损坏

•  行程开关线未接好或损坏

•  交流接触器未接好或损坏

•  有电时使用

•  接好开关线或更换开关

•  接好行程开关线或更换

•  检查接线或更换

机器嗡嗡响,不运转

三相电掉相

立即拉闸,请电工排除

电机反转

电线接错

三相线任意变换二相线

机器推不动

检查机座底下的万向轮,看万向轮是否已坏

更换万向轮

顶撑、脚撑卡不住,粉墙时机器后移

•  卡销松

•  卡销磨损

•  虎爪已磨平

•  拧紧卡销

•  修复或更换卡销

•  把虎爪磨尖

 

机器上升困难,无力

•  减速机没有加润滑油

•  皮带过松

•  升缩杆未抹机油

•  单相电机电压过低

•  减速机加满润滑油

•  张紧皮带

•  抹机油润滑

•  待电压稳定方可

搅灰板上升不转动或下降转动

 

离合器(飞轮)已坏

去掉焊点,更换同型号的离合器(飞轮),(自行车配件店有售)

 

行程开关失灵

•  三相电机线接反

•  连接行程开关电缆已断

•  行程开关已坏

•  任意两根火线更换位置

•  更换电缆

•  更换行程开关

搅叶转动时咔咔响或转不动

轴承内进入了沙灰或轴承损坏

拆卸轴承座检查,去掉沙灰加油密封或更换同型号轴承

机器运转有异常响声或钢丝绳卡住

•  钢丝绳跳出滑轮

•  钢丝绳已毛

•  把钢丝绳装进滑轮

•  更换钢丝绳

机器运转时摇摆

滑套上张紧螺丝太紧或太松

调整螺丝松紧度

 

所粉墙面下薄上厚或下厚上薄

上部没顶紧或顶撑虎爪没抓紧,脚撑没抓紧

•  顶紧上部

•  检查顶撑或肢撑,调整间隙虎爪

链条太松或掉链条

张紧轮太松

调好张紧轮

 

遥控装置不工作

•  电路没电或接触不良

•  遥控器无电

•  电路损坏

•  电机损坏

•  检查接插件

•  重新装电池

•  返修更换

•  返修更换

 

遥控顶杆卡滞不能伸缩

•  卡住螺丝松脱

•  螺丝不润滑或丝内淤油泥太重

•  拧紧卡住螺丝

•  加机油润滑或清洗淤泥后再润滑

Breakdown phenomenon

Breakdown reason Removes

the method Doe

Not move according to the switch owe

? blackout
? manual switch did not take good lines or damage
? Line Switches itinerary has not received good or damage
? AC contactor did not take good or damage

 

? AC contactor did not take good or damaged when an electric ? Use
? Switched access lines or good replacement Switches
? received good trip switch line or replacement
? Check wiring or replacement

Machinery humming sound, not running

 

Phase three-phase electricity swap

 

Immediately grounds, electricians exclusion

 

Motor reversal

Then the wrong wires

Three-Phase is arbitrary transform Line

Machinery real drive

 

Check underneath the seat Universal Wheels to see whether bad Universal Wheels

Replacement Universal Wheels

Top-shoring, feet up the card could not expanse retracting when machines

 

? Pine card sales
? Wear card
? continue to be seized already wear

 

? Tightening card sales
? repair or replacement card sales
? continue to be seized sharpened

Machines rose difficulties, inability

 

?? reducer no lubricating
? belt too loose
? The reduction or no-clean oil
? Single-phase low voltage motors

 

? reducer fill lubricants
? Belt Tensioner
? clean lubricating oil
? question voltage stability before

Gray plate stirred up not rotate or turn down

 

Clutch (flywheel) bad

Remove solder joints, replacement of the same type of clutch (flywheel), (bicycle accessories shop on sale)

The machine operates with abnormal sounds or rope jamme

? jump out of the pulley rope
? rope has hair

? rope over a pulley
? rope replacement

 

The machine operates at the swing

Slide tensioning screw is too lax or too strict

The whole screw tolerance

Powder on the wall under thick or thin under thick mine

Upper drowned or top up the bear did not seize continue to be seized, not seize the elevator fee

? Top tight upper
? Check the top or shoring up the limbs, adjusting gap continue to be seized
Seize

The chain is too lax or swap chain

Tension round is too lax

Tension is better round

Remote control devices do not work

? Circuit did not have access to electricity or
? remote control radio
? circuit damage
? motor damage

? Check plug
? reloading battery
? Rework replacement
? Rework replacement

Remote control rod catching not extendable

 

? jammed loose screws
? not screw lubrication or silk with heavy siltation grease

?  拧紧卡住螺丝

?  加机油润滑或清洗淤泥后再润

 

 

 

•  注意事项:

!?机器工作时,机器底下不能站人。
!?磨擦部位定期保养,钢丝绳、滑套、滑轮、立柱定期加润滑油。
!?减速机不能缺齿轮油,如有漏油现象,应立即添加,并查出漏油原因。
!?立柱架起后,检查钢丝绳是否入槽。如发现没有入槽及时调整;如钢丝绳卷乱,可全部抽出重新缠绕。卷钢丝绳头应走卷轴上面。
!?工作时应高度重视线路安全,开机前要检查各电源接线、开关、插头,插座是否牢固,有无破损,否则立即改正,必要时用万用表或试电笔检查,一切正常后方可开机。
!?严格规范作业,主机上升至顶梁,下降至底座,行程自控装置自动停机,若不停机,须马上检查行程自控装置电线是否接反,如接反马上调换二线,否则部件易损。
!?工作前,先要检查各连接螺母是否坚固无松动现象。特别注意钢丝绳扣是否牢固,否则立即改正。然后空车升降运行半小时。抹板面及上口边不能有死角灰块存在,搅拌轴须上升转动而下降不转。
!?粉墙过程中应尽量不停机,一次粉到顶部。
!?各种灰料严禁掺入大石子,浓度以适宜为好。
!?为了使立柱的伸缩管在工作中运动灵活,不致僵卡,立柱在安装运输过程中,严禁碰撞、挤压、敲打、摔打,以免凸凹变形或弯曲而不能正常使用。另外,如水泥水浆掉在上面要立即清理干净。防止生锈或沾有“死”灰 。
!?每天工作完,应清洗机器,并检修维护机器,以便下次使用。
!?如机器撂置一段时间不用,应作防腐处理。

 
地址:北京 朝阳区西大望路甲23号帝景大厦7楼29层 邮编:100022
厂址:中国·北京市平谷区兴谷工业开发区A区
开户:中国民生银行北京劲松支行
帐号:0131014170002746
电话:+86(010)51667961 51296729转606/601/603/602
传真:+86(010)51296729-605
网址:http://www.feiwanda.com
邮箱:feiwanda1@126.com
西南飞万达重庆分公司
地址:重庆市江北区南桥寺春城2栋
邮编:400021
网址:www.fn333.com
电话:023 89236283
传真:023 86793152
售后服务电话:023 60503215
QQ号:846913572
电子信箱邮箱:fwdcd@126.com

Address: 23 floor,7#, No.23, Xi Da Wang Road, Chao Yang District, Beijing, China Factory: A,Beijing Pinggu Developing Zoon, China Account Bank: China Minsheng Bank, Jinsong Branch

Account: 0131014170002746

Tel: 86-010-51661961 51296729-608/607/604/602 Fax: 86-010-51667961-605

Web: www.fwd863.com

E-mail: feiwanda@126.com

                       
QQ: 756649686 QQ: 351270849 QQ: 351064252
以上QQ24小时在线为您解答服务